進入公司首頁>
進口羅茨風機工作原理：
進口羅茨風機爲容積式風機，輸送的風量與轉數成比例，三葉型葉輪每轉動一次由2個葉輪進行3次吸、排氣，與二葉型相比，氣體脈動變少，負荷變化小，機械強度高，噪聲低，振動也小。在2根平相行的軸上設有2個三葉型葉輪，輪與橢圓形機箱内孔面及各葉輪三者之間始終保持微小的間隙，由於葉輪互爲反方向勻速旋轉，使箱體和葉輪所包圍著(zhe)的一定量的氣體由吸入的一側輸送到排出的一側。各支葉輪始終由同步齒輪保持正確的相位，不會出現互相碰觸現象，因而可以高速化，不需要内部潤滑，而且結構簡單，運轉平穩，性能穩定，适應多種用途，已運用於廣泛的領域。
進口羅茨風機技術參數：
壓力：9.8-98kpa
風量：0.49-261.9m3/min
轉速：590-2100r/min
功率：0.75kw-560kw
口徑：50-3500mm
進口羅茨風機的特點:
●由於採用瞭(le)三葉轉輪及帶螺旋線型的箱體，所以風機的噪聲的振動很小。
●葉輪和軸爲整體結構，且葉輪無磨損，風機性能持久不變，可以長期連續運轉。
●高速高效率，且結構非常緊湊。
●結構簡單，由於採用瞭(le)特殊軸承，具有超群的耐久性，使用壽命比國内風機長，且維修管理也方便
●由於附有齒輪油甩油裝置，因此不會産生漏油的現象。
進口羅茨風機轉子檢修的質量标準要求如下：
1、轉子不應有砂眼、氣孔等缺陷。
2、轉子組裝時兩端軸頸的平行度偏差應不大於0.02mm，兩端面與牆闆的平行度偏差應不大於0.05 mm。當風機進出口方向和主軸位置不變時，轉子壓力角間隙應在轉子水平線成45°角兩個位置上調整。不同型号的風機轉子各部間隙不同。
3、轉子應進行動靜平衡校驗。
4、軸與轉子垂直度公差應不大於0.05 mm。
進口羅茨風機運行條件：
1、輸送介質的進汽溫度通常不得大於 40℃。
2、介質中微粒的含量不得超過 100mg/m3，微粒*尺寸不得超過最小工作間隙的一半。
3、運轉中軸承溫度不得高於 95℃，潤滑油溫度不高於 65℃。
4、使用壓力不得高於銘牌上規定的升壓範圍。
5、羅茨鼓風機葉輪與機殼、葉輪與側闆、葉輪與葉輪間隙出廠時已調好，重新裝配時要保證該間隙。
6、羅茨鼓風機運行時，主油箱、副油箱油位必須在油位計兩條紅線之間。
進口羅茨風機美國泰樂TYLER售後服務：
*的服務鑄就*的企業讓客戶無後顧之憂。
1、按合同要求提供産品的合格證、銘牌、檢驗報告、産地證名、安裝說明書等。
2、顧客在驗收産品過程中，如出現與合同要求不符時，我司接到顧客通知後兩小時内給予處理。
3、我司提供十二個月以上産品質保期，時間從驗收合格之日起計算。
4、在正確安裝和使用下，出現産品質量問題，本公司将負責到底。
The United States imported roots blower roots blower
The working principle of imported roots blower:
Blower for volume blower, air transport and rotation is proportional to the trefoil impeller rotating each time by 2 to three times the impeller suction exhaust gas pulsation of small, small vibration, low noise. Fan impeller on 2 axes and oval shell hole surface, impeller end and the fan cover has always maintained a small gap between, on one side of the synchronous gear drives the wind from the fan inlet along the inner wall of the shell is transported to the discharge. The inner cavity of the fan does not need lubricating oil, the structure is simple, the operation is stable, the performance is stable, and the utility model is suitable for various purposes, and can be used in a wide range of fields. The characteristics of Roots blower with three rotor structure, and reasonable housing into the inner structure of import air outlet, so the fan small vibration and low noise, the impeller and shaft for the overall structure and the performance of the fan impeller wear free, persistent, can be long-term continuous operation.
Imported roots blower installation requirements:
Fan in the environment temperature of not more than 40 degrees C, can be used for a long time. In the summer, the exhaust fan should be installed and other cooling measures to improve the service life of the fan.
Imported roots blower application:
Sewage aeration water purification plant filter backwash vacuum dust removal material conveying
Widely used in various fields for municipal drainage, construction, petroleum, chemical, gas, food, pharmaceutical, power generation, metallurgy, mining, boiler steam system, pressure vessel, atomic energy, aerospace, rockets, and people's daily life. Shanghai Yi butterfly products sell well all over the country, high quality, efficient service, won the trust of users and a wide range of praise.
Imported roots blower technical parameters:
Pressure: 9.8-98kpa
Air volume: 0.49-261.9m3/min
Speed: 590-2100r/min
Power: 0.75kw-560kw
Caliber: 50-3500mm
Imported roots blower operating conditions:
The inlet temperature of 1, the transmission medium is usually not more than 40 DEG C.
The content of particles of 2 medium shall not exceed 100mg/m3, the maximum particle size should not exceed half of the minimum clearance.
3, the bearing temperature in operation shall not exceed 95 DEG C, the lubricating oil temperature is not higher than 65 DEG C.
4, shall not exceed the use of pressure boosting range specified on the nameplate.
5, roots blower impeller and casing, impeller, impeller and impeller clearance and side plate factory tuned, re assembly to ensure the gap.
6, roots blower operation, the main oil tank, fuel tank level must be two red line on the oil level between.
The United States imported roots blower tylosin TYLER customer service service:
The first-class service created a first-class enterprise so that customers no worries.
1, according to the contract requirements for product certification, nameplate, inspection report, certificate of origin, installation instructions etc..
2, the customer in the process of acceptance of the product, such as the emergence of the contract requirements and inconsistent, I received the notification of the customer within two hours after the treatment.
3, our company provides more than twelve months warranty period, the time from the date of acceptance.
4, in the correct installation and use, product quality problems, the company will be responsible in the end.
美國泰樂代理商上海凡而閥門有限公司，咨詢：
英國格林相關領域業績：杭州地鐵1号線、杭州地鐵2号線、杭州地鐵4号線，南京地鐵1号線、南京地鐵2号線、南京地鐵3号線、南京地鐵4号線、南京地鐵10号線。
帝國化學工業、美國科氏工業、美國聯合能源、艾默生電氣、盧克石油、中國海洋石油。
Green field performance: Hangzhou Metro Line 1, Hangzhou Metro Line 2, Hangzhou Metro Line 4, Nanjing Metro Line 1, Nanjing Metro Line 2, Nanjing Metro Line 3, Nanjing Metro Line 4, Nanjing Metro Line 10.
Imperial chemical industries, the United States of America, the United States, Emerson, Luke electric, China National Offshore oil.
我們的羅茨風機來自凱森品牌，我們的羅茨泵在德國工廠生産。
德國KAYSEN凱森進口羅茨風機概述
羅茨風機具有中等負載，*風量5709m3/h，*功率爲117KW。同步斜齒輪結構使風機具有更低的噪音及平穩的運行狀态。重載荷金屬支架軸承使風機在較高的載荷工況下依舊保持*的性能表現和更長的壽命。密封採用機械密封結構，確保其密封性更加優秀。該系列風機可以選擇水平安裝或者垂直安裝啦滿足不同的工況。
産品圖片
主要特點：
風機採用活塞環密封設計能夠滿足高轉速的要求，*轉速可達3000rpm，所有與密封面接觸的軸端面都經過抛光處理，以減少密封面的磨損，並降低其洩漏風險。擺線式葉輪線性設計能夠輸送更高壓力的氣體，*壓力可達1.05bar（g)。齒輪材質全部爲熱處理後的合金鋼，分體式齒輪設計更便於安裝拆卸。另外特殊的殼體設計，即使在輸送高壓力氣體時也無需水冷。
主要優點：
●軸承的選用較爲合理，各軸承的使用壽命均勻，從而延長瞭(le)風機的壽命
●風機油封選用進口氟橡膠材料，耐高溫，耐磨，使用壽命機種齊全，可滿足不同用戶不同用途的需要
●風機容積利用率大，容積效率高，且結構緊湊，安裝方式靈活多變
●葉輪和軸爲整體結構且葉輪無磨損，風機性能持久不變，可以長期連續運轉
主要應用：
●過濾器逆洗
●真空除塵
●物料輸送
●污水曝氣
●淨水廠
羅茨風機操作注意事項須知
羅茨風機操作注意事項
1、KAYSEN羅茨風機運行時做好記錄，以便早期發現異常，並給故障原因調查提供有利參數。
1) 電源電壓、運行電流值、頻率;
2) 吐出壓力;
3) 大氣溫度、吐出溫度、軸承部溫度;
4) 振動、噪音;
5) 潤滑油位、油髒污情況等。
2、KAYSEN羅茨風機流量調整方法：
流量大小不能通過開關閥門來調整。錦工羅茨風機是容積型壓縮機。關閉閥門，壓力上升，錦工羅茨風機超負荷運轉，易被燒壞。故出口管道的閥門必須完全打開。隻能通過調整頻率來改變轉速從而改變流量和軸功率或增設溢流管道來調整流量。
3、KAYSEN羅茨風機出口壓力表開關應處於長閉狀态，隻有在檢修後試機或需測定壓力時才将壓力表開關打開。
KAYSEN PUMP
羅茨風機選型指南
按類型、型号進行選擇
羅茨風機可分爲多種類型,例如材質堅硬、耐磨且具有一定防腐蝕效果的羅茨風機,該類型的羅茨風機一般适用於發電站、發電廠等場所;具有防爆功能的羅茨風機一般适用於産生易燃易爆氣體的場所;而通風性能好、排氣速度快的羅茨風機則比較适用於井底、隧道等通風性較差的場所。羅茨風機的型号由字母與數字組成,一般具有固定含義,可根據自身需求進行選擇。
按流量、轉速進行選擇
羅茨風機的流量有著(zhe)其自身的計算公式,根據公式來計算該羅茨風機的流量即可得到準確的流量系數。轉速的選擇則是根據葉輪的半徑、大小而決定的。
按風壓、效率進行選擇
風壓是氣體流經風葉時産生的壓力差值,可根據空氣密度、壓力系數等可測數據進行推算。不同的環境需要不同風壓的羅茨風機,因此要根據自身環境進行測量、推算,從而得到風壓的值,再根據風壓值選擇合适的羅茨鼓風機。羅茨風機的效率也是需要根據羅茨風機的風葉形狀、系數進行計算的。除此之外,羅茨風機的電功率的大小也決定瞭(le)羅茨風機的工作效率。
Roots Fan Selection Guide
Select by type and model
德國KAYSEN羅茨風機優點：
●軸承的選用較爲合理，各軸承的使用壽命均勻，從而延長瞭(le)風機的壽命
●風機油封選用進口氟橡膠材料，耐高溫，耐磨，使用壽命機種齊全，可滿足不同用戶不同用途的需要
●風機容積利用率大，容積效率高，且結構緊湊，安裝方式靈活多變
●葉輪和軸爲整體結構且葉輪無磨損，風機性能持久不變，可以長期連續運轉
Roots fan advantages
● The selection of bearings is more reasonable, and the service life of each bearing is even, which prolongs the life of the fan.
● The fan oil seal is made of imported fluoroelastomer material, which is resistant to high temperature and abrasion and has a complete service life.
● Large volume utilization rate, high volume efficiency, compact structure and flexible installation
●The impeller and shaft are of integral structure and there is no wear on the impeller. The fan performance is durable and can be continuously operated for a long time.
德國KAYEN羅茨風機使用的注意事項：
●起動前的準備：
檢查各部位緊固情況，檢查進、排氣管和機組在基礎上的安裝質量。
按照電動機銘牌要求接通電源，確認電動機轉向正確後再與鼓風機接通，鼓風機嚴禁反轉，電動機功率≥22KW時，應採用降壓啓動裝置。
向軸承油箱和齒輪油箱内加入潤滑油，油量應加到圓形油标的中線。
全部打開進排氣管道上閥門，用手盤動鼓風機主動軸，應靈活無阻滞，仔細傾聽有無不正常響聲。
●空負荷試運轉：
空負荷試運轉是指鼓風機在進排氣口閥門全部打開情況下進行的試運轉，新安裝或大修後的鼓風機都應該空負荷試運轉，持續時間不少於30分鍾，(排氣出口可採用放空裝置)，靠近風機出口處，一定要安裝放空閥，風機試運轉後，慢慢關掉放空閥，請按銘牌上的壓力使用，嚴禁超壓使用。
試運轉時應注意鼓風機有無不正常的撞擊、摩擦等響聲，各部位不允許有過高的溫度，不正常的氣味或冒煙現象，還應檢查軸承處振動是否正常，如有上述現象，應立即停機，查明原因，排除故障。
●正常帶負荷持續運轉：
經試運轉良好的機組，方可帶負荷持續運轉，此時逐步緩慢地調節閥門，直到滿負荷，切不可一次突然升壓到滿負荷，也不允許超負荷運轉，以免損壞機組。
正常運轉時油箱内用普通機油潤滑時，機油溫度一般不應高於65C°。軸承部位在X、Y、Z三個方向的振動速度均方根值(有效值)應不大於11.2mm/S。
Precautions for using roots fans
●Preparation before starting:
Check the tightening of each part, and check the installation quality of the intake and exhaust pipes and the unit on the foundation.
Connect the power supply according to the motor nameplate, and confirm that the motor is turning correctly before connecting it to the blower. The blower is strictly prohibited to reverse. When the motor power is ≥ 22KW, a step-down starting device should be used.
Add lubricating oil to the bearing oil tank and gear oil tank, and the oil volume should be added to the center line of the round oil gauge.
Fully open the valves on the inlet and exhaust pipes, and move the active shaft of the blower by hand. It should be flexible and non-blocking. Listen carefully for abnormal sounds.
● No-load test run:
No-load test run refers to the test run of the blower with all the inlet and exhaust valves open. Newly installed or overhauled blowers should be run at no load for a duration of not less than 30 minutes. (Exhaust outlets can be used Vent device), near the fan outlet, be sure to install a vent valve. After the fan is commissioned, slowly turn off the vent valve. Use it according to the pressure on the nameplate. Overpressure is strictly prohibited.
During the test run, pay attention to the blower for abnormal impact, friction and other sounds. Excessive temperature, abnormal odor or smoke should not be allowed in each part. Also check whether the vibration at the bearing is normal. Shut down immediately, find out the cause, and troubleshoot.
●Continuous operation under normal load:
Only after the well-tested unit can continue to run with load, at this time slowly adjust the valve until it is fully loaded. Never suddenly increase the pressure to full load at one time, and do not allow overload operation to avoid damage to the unit.
When the oil tank is lubricated with ordinary oil during normal operation, the oil temperature should generally not be higher than 65C °. The root-mean-square value (effective value) of the vibration velocity of the bearing part in the three directions of X, Y and Z should not be greater than 11.2mm / S.
凱森的承諾
服務伴随永遠
無論在您購買前或是購買後，我們會堅持爲你提供優質的服務。購買前我們可以提供專業優質的購買咨詢服務、設備設計和選型建議等服務；購買後，我們可以提供安裝、安裝指導顧問式的服務，保證産品可以順利安裝使用；若您使用過程中有任何疑問，我們将會第一時間給你提供專業的解答和幫助！
快速高效的服務
在整個德國、歐洲和中國大部分城市可以提供快速的現場支持。我們的經銷商都是具有泵相關技術服務能力的公司，同時，凱森的工作人員都定期組織安裝、故障處理和維護保養等知識的學習，保證工作人員都可以快速高效的處理問題。
Kaysen Promise
Service accompanied forever
No matter before or after you buy, we will insist on providing you with excellent service. Before purchase, we can provide professional and high-quality purchase consulting services, equipment design, and selection recommendations. After purchase, we can provide installation, installation guidance and consulting services to ensure that the product can be installed and used smoothly. If you have any Questions, we will provide you with professional answers and help as soon as possible!
Fast and efficient service
Fast on-site support is available throughout most cities in Germany, Europe and China. Our distributors are companies with pump-related technical service capabilities. At the same time, Kasen staff regularly organizes learning of installation, troubleshooting and maintenance to ensure that staff can deal with problems quickly and efficiently.
進口羅茨風機（總代理）
長春羅茨鼓風機三葉羅茨鼓風機生産商購羅茨鼓風機
山東錦工有限公司
地址：山東省章丘市經濟開發區
電話：0531-83825699
傳真：0531-83211205
24小時銷售服務電話：15066131928
